Using GNSS for guidance
Configure the machine to connect to the Global Navigation Satellite System (GNSS) for machine guidance.
To enable GNSS guidance, select a GNSS option as the positioning source in the Machine Setup screen.
The GNSS Correction Source screen
The GNSS Correction Source screen enables you to set the active correction source. You can access it via the System Settings menu .
NOTE – Changing between correction sources may cause your position to shift.
Depending on your user permissions, you can create and configure GNSS correction sources via the Web Interface. Tap Advanced to launch the Web interface.
There are different levels of precision and accuracy available from GNSS. These depend on the GNSS technology that you use. The different methods available for delivering GNSS to a rover include:
- SNRxxx radios—Conventional Real-Time Kinematic (RTK) over a wireless data radio.
- Internet—Virtual Reference Station (VRS) RTK over the Internet.
- Wi-Fi local base station—SNM940 with Wi-Fi enabled can be used as a local base station. It automatically establishes a Wi-Fi connection with the rover(s) and transmit RTK corrections to it.
- Internet Base Station Service (IBSS)—RTK over the Internet using cellular services. It is delivered via a Connected Community account.
The GNSS Precision Tolerance screen
The GNSS Precision Tolerance screen enables you to set the tolerance or level of accuracy. You can access it via the System Settings menu .
Make sure that the selected GNSS precision tolerance is appropriate for the work you are about to do. Note that in certain conditions, poor quality signal transmission may mean that GNSS accuracy is continually less than that allowed by the grade tolerance. Atmospheric conditions can impact upon the quality of signal transmissions broadcast from satellites. Also, the distance you are operating from the base station can affect signal quality. The higher the accuracy mode, the lower the tolerance for errors.
GNSS receiver status indicators
The MS9xx GNSS receivers have three LEDs next to the harness connector. The behavior of these LEDs indicate the status of the receiver.
|
1 |
Power |
2 |
Data link |
3 |
Satellite |
The meaning of the receiver status LED activity is shown below:
|
LED |
Off |
Slow flash |
Flash |
Fast flash |
On solid |
|---|---|---|---|---|---|
| Power | No power | Beta test period expired1 | Power on | ||
| Data link | No CMR™ data received or too few satellites | CMR data type 0 being processed | 10 Hz CMR data being processed | ||
| Satellite | No satellites being tracked | Tracking four satellites or more | Tracking three satellites or less | Monitor mode2 |
1 In addition to the power LED, the data link and satellite LEDs will also flash, and at the same rate as the power LED.
2 In addition to the satellite LED, the power LED will also be on solid, and the data link LED will flash.
When GNSS is working correctly in a single-GNSS system, you will see the following activity:
- The power LED will be on solid.
- The data link LED will flash at 1 Hz.
- The satellite LED will flash slowly.
When GNSS is working correctly in a dual-GNSS system, you will see the following activity:
- The left GNSS receiver’s LEDs will behave as described above in the single-GNSS system.
- The right GNSS receiver’s power LED will be on solid.
- The right GNSS receiver’s data link LED will be on solid.
- The right GNSS receiver’s satellite LED will flash slowly.
GNSS text items
Useful text items for GNSS are:
- GNSS Precision Tolerance (Fine, Medium, Coarse)
- Satellite Count
- Vertical GNSS Precision
- Horizontal GNSS Precision
To add, remove or re-order the text items, touch and hold anywhere in the text ribbon (across the bottom of the guidance view). A screen displays that lets you configure your text items.
Troubleshooting
You can use the Satellite Count text item to view the number of satellites used for the current position solution. The satellites must be visible by both the base station and the machine. You need five or more satellites to initialize, and four or more to continue working.
For further GNSS diagnostics, your technician can access GNSS details via the Web Interface.
For information about error messages that may appear on the work screen, see Using GNSS