2026.20

Version 2026.20 of the Trimble® Access™ software is available from November 2026.

These Release Notes describe the new features and changes available in this release of the Trimble Access software. Alternatively, you can download these release notes as a PDF file.

Hardware support

Support for the new Trimble ST30 smart target

Trimble Access version 2026.20 supports the new ST30 smart target. The ST30 smart target offers a powerful new way of working, with:

  • Automatic rod height measurements

    Eliminate costly rework caused by one of the most common field mistakes – forgetting to change the rod height - and give yourself continuous peace of mind and data integrity.

  • IMU-based tilt compensation

    Speed up your surveys and stakeout with the IMU-based tilt compensation, enabling you to capture shots without needing to perfectly level the rod every time. This capability also allows for easy measurements of previously inaccessible or hard-to-reach points, minimizing extra instrument setups and eliminating complex COGO offsets.

  • GeoLock

    GNSS-assisted Autolock. Designed specifically for when you are surveying using a robotic total station, when lock to a prism is lost, GeoLock uses the GeoLock data stream from the ST30 to turn the instrument to your GNSS location before using Autolock to lock back onto the prism.

The ST30 is a Bluetooth Long-range Robotic (BLR) device. To use the device in Trimble Access, you must pair to the device from the Bluetooth tab of the Connections screen in Trimble Access. Pairing with a Trimble BLR device using the controller operating system Bluetooth screen will prevent the Trimble Access software from being able to connect to the device.

NOTE – In addition to Trimble Access General Survey, Trimble Access Roads, Tunnels, and Mines support the ST30 smart target. All other specialized Trimble Access field applications do not currently support conventional IMU-based tilt compensated measurements.

For more information, see the topic Trimble ST30 Smart Target in the Trimble Access Help, or check out the ST30 smart target video series on the Trimble Access YouTube channel.

Support for new TDL310 radio

Trimble Access version 2026.20 supports the new Trimble TDL310 radio. The TDL310 is a 351 MHz radio for use in Japan.

TCU5 controller no longer supported

Trimble Access version 2026.20 and later cannot be installed on Trimble TCU5 controllers, regardless of software warranty or subscription status. The TCU5 runs an older Android operating system that no longer receives security updates. Ending support for the TCU5 enables Trimble Access to stay aligned with current, more secure platforms. TCU5 controllers can continue running Trimble Access version 2026.1x.

New features and enhancements

BCF Topics

Trimble Access General Survey now supports BCF (BIM Collaboration Format) Topics, connecting field crews directly to Trimble Connect's cloud-based issue management workflow.

BCF Topics give survey and construction teams a standard way to capture, assign, track, and resolve project issues - with 3D viewpoints, screenshots, and location context - without leaving their daily Trimble Access workflow.

A BIM model is not required to use BCF Topics. When a model is on the controller, Topics can be linked to 3D viewpoints and map context for instant visual clarity. When no model is available, crews can still create and manage Topics using text, comments and image attachments.

To open the BCF Topics panel, tap on the BIM toolbar.

For more information, see the topic Creating, accessing and updating BCF Topics in the Trimble Access Help.

Downloading BIM files from Trimble Connect

We have improved the behavior when downloading BIM and 3D models to the controller from Trimble Connect.

  • The Download as TrimBIM check box in the Cloud sync settings screen is now named Download IFC as TrimBIM to better reflect that this setting applies only to IFC files.

    • Select the Download IFC as TrimBIM check box to download IFC files as TrimBIM .trb files.

    • Clear the Download IFC as TrimBIM check box to download IFC files from Trimble Connect in their original .ifc or .ifczip file format.

  • All other BIM model file types including DWG and SKP are now always downloaded from Trimble Connect as TrimBIM .trb files, whether or not the Download IFC as TrimBIM check box is selected.

TrimBIM (.trb) files are Trimble's proprietary, lightweight 3D model and BIM exchange file format optimized for performance across Trimble applications.

Automatic uploads to the cloud now apply to field data only

Enabling the Automatically upload the current project option to upload changes to the cloud at regular intervals or when you complete specific actions now applies only to field data changes. These settings no longer apply to any changes made to project design files on the controller, as such changes are expected to be rare.

To upload changes to design files from the field, tap the cloud icon next to the file name in the Project data list.

For more information, see the topic Cloud settings for all projects in the Trimble Access Help.

Gridline station setup

The new gridline station setup allows you to determine the instrument position by making observations to two intersecting gridlines. Measure two points on each gridline, review the computed solutions, then accept the setup. This is useful on construction sites where layout is driven by design gridlines and traditional survey marks or control points are not available. Crews can orient the instrument to the design and start layout using the site information they already have.

After accepting the setup, you can measure a reference elevation so heights are controlled for subsequent work.

NOTE – For the best accuracy, Trimble recommends using a Resection rather than a Gridline setup. The Gridline method is intended as a secondary workflow when standard control configurations are unavailable.

For more information, see the topic To complete a gridline in the Trimble Access Help.

New Change face button

When Trimble Access reports that an observation is on the wrong face during station setup, station setup plus, resection rounds, or rounds, the message now includes a Change face button if the connected instrument can change face.

Line and polygon codes on Cogo points

When the feature library uses Store polylines with codes on lines, points created from the Cogo menu now behave the same way as measured or keyed-in points:

  • Assigning a line or polygon code creates the matching linework in the map and in the job.

  • The software prompts for line and polygon attributes, including when a Cogo function stores more than one point.

  • Point attributes and line or polygon attributes are both stored.

This applies to Subdivide a line, Subdivide an arc, area subdivision, Compute point, Compute average, Traverse, Transformations, and Arc solutions. Taped distances already worked this way.

GeoLock

  • The Joystick screen now includes a Turn softkey. Turn turns the instrument to the GNSS position and does not start a search. The Joystick screen stays open if the turn or a search does not lock onto the target.

  • When using GeoLock the satellite map icon is no longer shown once a conventional survey has started and the instrument is locked to the target, so the icon does not cover points in the map.

GNSS signal tracking

Galileo E6 signal tracking is now enabled in all survey types for receivers with GNSS firmware version 6.60 or later and capable of tracking the Galileo E6 signal. The Galileo High Accuracy Service (HAS) is not supported.

GNSS Navigation Message Authentication

For receivers that support Navigation Message Authentication (NMA) with firmware version 6.60 or later, Trimble Access no longer disables MSS RTX SV tracking when starting or ending surveys that don't require RTX positioning. This allows receivers configured to use NMA to continue authenticating GNSS signals without interruption.

RTX QuickStart removed

We have removed the QStart softkey from the RTX status screen. RTX QuickStart is no longer available, because an incorrect known-point coordinate can cause the receiver to converge on the wrong position.

Coordinate System Database updates

The Trimble Coordinate System Database installed with Trimble Access includes the following enhancements:

  • Added support for modernized NSRS beta 3.

  • Fixed the Modernized NSRS beta 2 in Guam and American Samoa.

  • Added support for the new Mexican Geoid Model 2025.

  • Added displacement model, datum and zones for ITRF2005@2008.83 used in Thailand.

  • Updated the Geoid model for Latvia to use LV14_2020 with zones LKS-2020 & LKS-92 to LKS-2020.

  • Updated DB_REF datum to use realization ETRS89-DREF91(R25) at epoch 2021.48.

  • Fixed the name of Malaysian vertical datum.

  • Fixed the displacement model used with SPCS2022 beta 2 zones.

  • Improved RTX support in Greece.

Improved voice messages

Based on customer feedback, we have reinstated the voice previously used in Trimble Access before version 2025.20. With Trimble Access 2026.20 you can install English voice messages in the familiar Trimble Access voice.

Resolved issues

  • Local files referenced as linked files: We have fixed an issue where occasionally project files that were local to the controller were added as linked files references in the cloud project. This caused issues in downstream services including invalid references, upload failures, synchronization issues, and display errors.

  • Export: We have fixed an issue introduced in Trimble Access version 2026.10, where if you changed the export folder to the project root folder the selected export location was not remembered for subsequent exports.

  • Global reference datum: We have fixed an issue where the global reference datum was not set correctly when downloading a project from Trimble Connect where the coordinate system used a datum grid.

  • Stakeout: We have fixed the following issues:

    • The point highlighted in the stakeout list was not highlighted on the map.

    • When staking out lines from 12da files containing arcs, the arcs were not displayed correctly, and could not be staked.

    • Stakeout graphics did not change to bullseye mode on the T70 controller.

  • Feature library symbols: We have fixed the following issues when using symbols from a feature library:

    • Block symbols disappeared from the map after you stored a point that prompts for attributes.

    • Reading block definitions from FXL schema version 9.6. Information for all block definitions is now available and blocks are displayed correctly.

  • LandXML: We have improved our handling of LandXML files encoded as iso-8859-1 (Latin-1). Previously, such files could result in entity names not being displayed correctly, and application errors on Android devices.

  • Snap to intersection: We have fixed an issue where the Snap to intersection function did not always work correctly with parallel lines.

  • Map tap-and-hold menu: The following items in the Map tap-and-hold menu were missing when running Trimble Access with a GNSS-only license: Create from selection, Insert into polyline, Remove from polyline, Key in circle.

  • Receiver internet TLS: We have fixed an issue where a VRS or NTRIP connection that used the receiver modem did not enable TLS on the receiver, even when Use TLS was selected. Connections that used the controller internet were not affected.

  • Dual prism offset: We have fixed an issue where accidentally selecting dual prism offset, and then changing the offset mode back, could freeze the software. Trimble Access could then fail to open.

  • R580 data logging: We have fixed an issue in FastStatic and PPK survey styles where setting the antenna type to R580 removed the logging device field and forced logging to the controller. You can again choose to log data to the receiver.

  • SX12 connections: The instrument and software now behave more reliably when switching from a Wi-Fi to Wi-Fi HaLow connection or back.

  • SX12 reconnection: We have fixed an issue where Trimble Access froze when reconnecting to an SX12 after the instrument battery was replaced during a survey.

  • WMS map layers: We have fixed an issue where selecting a large number of layers in a WMS service could result in no map content being displayed.

  • Integrated surveying resection: We have fixed an issue in an integrated surveying resection with GNSS running, where entering a backsight point name that was not in the job showed an error with no GNSS option. We have restored the prior behaviour where tapping Measure offers GNSS measurement.

  • Auto attributes: We have fixed an issue where some auto attribute values were not displaying in Point manager or Review job.

  • Measure to surface: We have fixed an issue where using Measure to surface on Android controllers, including the TSC710, could cause the software to freeze.

  • GeoLock didn't turn: We have fixed an issue where GeoLock would not turn the instrument to the GNSS position during stakeout if the instrument connection had experienced a temporary disconnect, and the instrument had lost lock on the target at the time.

  • Release subscription setting: We have fixed an issue where the release subscription option in the About screen was not saved when exiting via the back button, Esc, sign out, or shutdown.

  • Tunnel profile field report: We have fixed an issue where charts and station data were missing when using Save as PDF to export a Tunnel profile field report.

  • SP60: We have fixed an issue introduced in Trimble Access version 2026.10, where the software would not connect to the internal radio of the SP60 receiver.

    TIP – If the attempt to connect does fail initially, Trimble recommends allowing around 15 seconds between attempts.

  • Application errors: We have fixed several issues that caused occasional application errors when using or closing the software. In particular:

    • When rapidly pressing the Enter and Back keys on a controller running the Android operating system (for example during stakeout).

    • When tapping one of the on-screen turn buttons in the SX12 video view while the Wi-Fi connection to the SX12 was down.