Tracking
Select Receiver Configuration / Tracking.
Elevation Mask – Enter the elevation, in degrees, below which the receiver will not track satellites.
List of satellites – Shows a list of satellite signals and if they are enabled or disabled.
|
Type |
Signal |
Description |
|---|---|---|
|
GPS |
L1 - C/A |
The receiver will track the C/A code of the GPS L1 band. |
|
L1C |
The receiver will track the C code of the GPS L1 band. |
|
|
L2E |
Enable or disable the tracking of the L2E signal by the receiver. You can choose to track either the L2C or L2E signal, or the L2C and L2E signal. |
|
|
L2 |
Set which information of the L2 signal the receiver is to observe: CL or CM + CL. |
|
|
L2 – Legacy |
The receiver will track the full cycle carrier phase of the L2 signal. CS code will not be tracked even if available. |
|
|
L2CS with Legacy fallback |
The receiver will track the CS code on the GPS L2 band if available. If CS code is not available, the receiver will track full cycle carrier phase in Legacy mode. |
|
|
L2CS with Legacy |
The receiver will track both CS and Legacy code simultaneously. |
|
|
L2 – CS |
The receiver will track the CS code on the GPS L2 band if available. If CS code is not available, the receiver tracks full cycle carrier phase in Legacy mode. |
|
|
L2CS – CM/CL |
The receiver will track both the CM and CL code broadcast by the satellite simultaneously. Trimble recommends that you use this setting. |
|
|
L2CS – CL |
The receiver will track only the CL code broadcast by the satellite. |
|
|
L5 |
If L5 is installed, this menu item is displayed. If selected, it allows tracking of the GPS L5 band. Set which code the receiver is to track: L5 – Q: The receiver will track only the Q code broadcast by the satellite. L5 – I + Q: The receiver will track both the I and Q code broadcast by the satellite simultaneously. Trimble recommends that you use this setting. |
|
|
SBAS |
L1 - C/A |
Enable or disable the tracking of the L1 C/A signal transmitted from SBAS satellites such as WAAS. |
|
L5 |
Enable or disable the tracking of the L5 C/A signal transmitted from SBAS satellites such as WAAS. |
|
|
GLONASS |
L1 - C/A |
The receiver will track the C/A code of the GLONASS L1 band. |
|
L1P |
The receiver will track the P code of the GLONASS L1 band. |
|
|
L2P |
The receiver will track the P code of the GLONASS L2 band. L2-P is the recommended setting. |
|
|
L2 - C/A |
The receiver will track the C/A code of the GLONASS L2 band. |
|
|
L3 |
The receiver will track the GLONASS L3 band. If you enable GLONASS L3, select either the Data + Pilot or Pilot option. Data: Carries the navigation message. |
|
|
Galileo
|
E1 |
The receiver will track the Galileo E1 band. |
|
E5-A |
The receiver will track the Galileo E5a band. |
|
|
E5-B |
The receiver will track the Galileo E5b band. |
|
|
E5-AltBOC |
The receiver will track the Galileo E5-AltBOC modulation. |
|
|
E6 |
The receiver will track the Galileo E6 band. |
|
|
BeiDou |
B1 |
The receiver will track the BeiDou B1 band. |
|
B1C |
The receiver will track the BeiDou B1C band. |
|
|
B2 |
The receiver will track the BeiDou B2 band. |
|
|
B2a |
The receiver will track the BeiDou B2a band. |
|
|
B2b |
The receiver will track the BeiDou B2b band. |
|
|
B3 |
The receiver will track the BeiDou B3 band. |
|
|
QZSS |
L1-C/A |
The receiver will track the L1-C/A signal of the QZSS satellites. |
|
L1S |
The receiver will track the L1-SAIF signal of the QZSS satellites. This signal is only of use for SBAS operation when in the Japan territory. |
|
|
L1C |
The receiver will track the L1C signal of the QZSS satellites. |
|
|
L2C |
The receiver will track the L2C signal of the QZSS satellites. |
|
|
L5 |
The receiver will track the L5 signal of the QZSS satellites. |
|
|
L6 |
The receiver will track the L6 (LEX) signal of the QZSS satellites. |
|
|
NavIC |
L5-C/A |
The receiver will track the L5-C/A signal of the NAVIC satellite. The default setting is Disabled. |
